The CDBM CDBC is a quad bilateral switch in- tended for the transmission or multiplexing of analog or digi- tal signals It is pin-for-pin compatible with. Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise . CD Datasheet, CD Quad Bilateral Switch Datasheet, buy CD
|Published (Last):||7 August 2004|
|PDF File Size:||18.69 Mb|
|ePub File Size:||17.10 Mb|
|Price:||Free* [*Free Regsitration Required]|
So you will see that if you press down the pushbutton with an analog signal or digital signal at the input, that same signal will appear at hte output.
In this circuit, we will show the basic functionality of the chip by passing analog signals through 2 of the switches by digital control. Each switch has a single input and a single output terminal. When unpressed, the pushbutton has the signal LOW by default.
With the control switch HIGH, then cd0466 switch closes and there can be an output.
This enables the signal at the input to go to the output. Datasheet current can flow in one direction and the other direction, depending on which side is the input. First, to power thewe connect 5V of power to V DDpin 14, and we connect the ground pin, pin 7, to ground. How the Circuit Works So, in order for this circuit to work, the pushbutton must datashset pressed down for each of the switches. The pinout of the chip is shown below. For this circuit, we are only going to be using 2 of the 4 switches.
CD Datasheet(PDF) – Intersil Corporation
How to Build a Quad Bilateral Switch Circuit In this circuit, we will show how to connect a bilateral switch chip to inputs and outputs using the quad bilateral switch chip. The quad bilateral switch chip is a chip that is made up of 4 switches. So by a HIGH digital signal fed into the control terminal, we can pass cd4606 analog signal from the input terminal to the output terminal of the switch.
The is a quad bilateral switch circuit, meaning that is composed of 4 switches.
How to Build a 4066 Quad Bilateral Switch Circuit
The really functions as an analog switch. The datasheet for the can be found at the following link: You can view the control terminal as the signal which closes the switch so that the input signal can cross over to the output. If a signal dahasheet fed into the input while the pushbutton is unpressed, no signal will appear at the output.
In order for signals to pass through from the input side to the output side, the control or enable terminal must be HIGH. To the inputs of the 2 switches, we feed an analog signal.
HTTP This page has been moved
Each switch has an datasbeet, output, and control terminal. Applying these principles, you can easily see how to use all 4 switches if wanted. As the quad term implies, the is composed up of 4 switches. In this circuit, we will show how to darasheet a bilateral switch chip to inputs and outputs using the quad bilateral switch chip. One place it can be obtained is at Taydaelectronics at the following link: The control terminal enables the input to go to output.
When pressed down, the pushbutton makes the signal HIGH. The is a pin chip. Each switch also has a control or enable terminal.
A bilateral switch is so called because the switch can operate forward or reverse. V DD and ground, pins 14 and 7, are the power pins. If the pushbuttons are not pressed down, then no signal will appear at the outputs. The has a wide operating voltage c4d066 5VV. This establishes sufficient power to the chip.
Without the control or enable switch, there can be no output. A bilateral switch acts as a single pole, single throw switch. The is an IC composed datasneet switches which are designed to switch analog signals via digital control. The switches are labeled from 1 to 4. To the control terminals of the 2 switches, we connect a pull-down resistor pushbutton circuit.
It can be obtained cheaply at a number of online electronic retailers. What this means is we feed an analog signal into the input of the switch and it reaches the output only if a HIGH digital signal is fed into the control or enable terminal.
This means that either side of the dafasheet can be used as the input. The most common cd44066 is a sine wave.